A product that doesn't fit the job's printable area is flagged Too big in the Artworks list and left out of the run. Tile it instead: the product is split into overlapping tiles, each tile becomes a piece of the job, and the run nests, prints and cuts the tiles like any other piece.
Tile a product#
Select the product and, on the Parts tab, press Tile this product… in the Tiling block. The tiling editor opens on a drawing of the product:
- Pick the direction: Vertical puts the tiles side by side (the seams run top to bottom), Horizontal stacks them (the seams run left to right), Grid cuts both ways.
- Set the overlap: the band two neighbouring tiles both print, so you can lap one over the other when you mount them.
- Leave the seams where the editor puts them, or drag a seam, type its position, or ask for a number of equal tiles. A tile larger than the media takes is hatched, with a warning, and the editor won't apply it.
- Apply.
The editor starts with tiles as large as the media takes: the job's printable width and height, less the product's bleed on both sides. On a roll both limits are the printable width, since a strip can be turned along the roll. Seams you don't place by hand keep following the media: change the sheet, the roll or the margins and the tiles are worked out again when the next run starts.
For example, "Banner 120x30" (120 × 30 in) on a 54 in roll with 0.5 in margins and a 1 in overlap becomes three vertical tiles: two of 53 in and one of 16 in, each 30 in tall.
Tiles in the job#
The product stays in the Artworks list, marked Tiled, with its tiles listed under it, each tagged tile 1/3, tile 2/3 and so on (numbered left to right, then top to bottom). In a run, the tiles are the pieces: the product itself is not nested, and the item count and total quantity at the bottom of the list still count it once.
- A tile shows exactly its part of the artwork, with the overlap. Its bleed comes from the artwork around it, so neighbouring tiles continue each other.
- A tile is cut on its own outline. For a product with a shaped outline, each tile is cut to that shape; cut lines inside the product (creases, windows) are not carried onto its tiles.
- Every setting is the product's: quantity, rotation, grain, mirror, bleed, material, properties, inks and the back of a two-sided item. Change them on the product and its tiles follow. A tile's own inspector is read-only and links back to its product.
- Ten of a product in three tiles is ten of each tile.
- Deleting the product deletes its tiles. A tile can't be deleted by itself: change the tiling, or remove it.
Note: When the product changes
Tiles are rebuilt whenever the product's shape, page or file changes. Seams you placed by hand are kept when they still fit; otherwise the tiles go back to as large as the media takes. If the product now fits in one piece, its tiling is removed and a warning on the product says so.
Change or remove a tiling#
On a tiled product the Tiling block shows the tile count and direction, with:
- Vertical / Horizontal: switch the direction, keeping the overlap, with seams as large as the media takes;
- Edit tiles…: open the editor again on the current seams;
- Tiling report: a page with the tile files and a plan of where each tile goes, for the installer (PDF products);
- Remove tiling: delete the tiles; the product is one piece again, and Too big if it still doesn't fit.
A tile that is still flagged Too big doesn't fit the other way: vertical tiles of a product taller than the sheet, for example. Use Grid, or the other direction.
From the API#
POST …/artworks/{id}/tile/ tiles a product, and returns every artwork of the job. The body is in points:
direction (vertical, horizontal or grid), overlap, and optionally x_cuts / y_cuts (seam positions from
the product's left and top edges; leave them out for seams as large as the media takes) and max_width /
max_height (the largest tile; leave them out to follow the job's printable area). An empty body or
{"clear": true} removes the tiling. See Imposition API.
{"direction": "vertical", "overlap": 72, "x_cuts": [2880, 5760]}