The presets library

Published specs for cutting tables, roll cutters, wide-format printers and finishing machines: what a preset copies, what is estimated, every model.

Presets are the published specifications of cutting machines and wide-format printers. Adding equipment from a preset saves you typing in a data sheet, and gives the time estimates sensible starting values.

Using a preset#

On the Equipment page, press Add machine or Add printer. Search by model or manufacturer, filter by type, and pick a model to see its published specs, the starting values the app will use, and the sources the figures came from. Each preset is labelled Manufacturer data or Secondary source, depending on where its figures were found.

Adding a preset copies its values into a new machine or printer that belongs to your team. You can edit every value afterwards, and later changes to the library never change your equipment.

Published figures and estimated starting values#

A preset holds what manufacturers publish: the working area or print width, maximum speed and acceleration for cutters, and the speed and passes of each print mode for printers. A missing figure shows as Not published.

Data sheets give ceilings, not the speeds shops actually run at, and never list setup or handling times. So the app fills those in with practical starting values and marks them estimated on the settings page:

Cutters: a cutting speed below the published maximum for flatbeds (and each roll cutter's documented factory speed for vinyl), corner lifts for tangential knives, plunge, overcut, registration, conveyor and setup times typical for the machine type. A missing acceleration gets a typical value.
Printers: a production print mode as the default, setup and board handling times, and a dry time for solvent inks.

Estimated values are a starting point. Time a real job and calibrate: see Cutting machines and Printers.

Note: Prices are never filled in

Hourly cost, hourly rate, minimum charge and ink cost and price start at zero on every preset. Set your own before you quote.

Cutting machines#

Working areas are in millimetres; a roll cutter shows its width only. The maximum speed is the manufacturer's ceiling.

Cutting machine presets
Maker	Model	Type	Working area (mm)	Max speed (mm/s)
Zünd	G3 L-2500	Flatbed cutting table	1,800 × 2,500	1,414
Zünd	G3 L-3200	Flatbed cutting table	1,800 × 3,200	1,414
Zünd	G3 XL-3200	Flatbed cutting table	2,270 × 3,200	1,414
Zünd	G3 3XL-3200	Flatbed cutting table	3,210 × 3,200	1,414
Zünd	S3 M-1200	Flatbed cutting table	1,330 × 1,230	1,414
Zünd	S3 L-1200	Flatbed cutting table	1,800 × 1,230	1,414
Zünd	S3 XL-1200	Flatbed cutting table	2,270 × 1,230	1,414
Zünd	D3 L-3200	Flatbed cutting table	1,800 × 3,200	1,414
Zünd	D3 XL-3200	Flatbed cutting table	2,270 × 3,200	1,414
Zünd	D3 3XL-3200	Flatbed cutting table	3,210 × 3,200	1,414
Zünd	Q-Line Q 18-32 D	Flatbed cutting table	1,800 × 3,200	2,800
Zünd	Q-Line Q 32-32 D	Flatbed cutting table	3,210 × 3,200	2,800
Kongsberg	X20 Edge	Flatbed cutting table	1,680 × 1,270	500
Kongsberg	X24 Edge	Flatbed cutting table	1,680 × 3,200	500
Kongsberg	X24	Flatbed cutting table	1,680 × 3,200	833
Kongsberg	X44	Flatbed cutting table	2,210 × 3,200	833
Kongsberg	X46	Flatbed cutting table	2,210 × 4,800	833
Kongsberg	C24 Edge	Flatbed cutting table	1,680 × 3,200	1,250
Kongsberg	C64 Edge	Flatbed cutting table	3,210 × 3,200	1,250
Kongsberg	C24	Flatbed cutting table	1,680 × 3,200	1,666
Kongsberg	C44	Flatbed cutting table	2,210 × 3,200	1,666
Kongsberg	C64	Flatbed cutting table	3,210 × 3,200	1,666
Kongsberg	C66	Flatbed cutting table	3,210 × 4,800	1,666
Kongsberg	XN24 (legacy)	Flatbed cutting table	1,680 × 3,200	833
Kongsberg	XN44 (legacy)	Flatbed cutting table	2,210 × 3,200	833
Kongsberg	XP24 (legacy)	Flatbed cutting table	1,680 × 3,200	1,667
Kongsberg	XP44 (legacy)	Flatbed cutting table	2,210 × 3,200	1,667
Colex	Sharpcut SX1717	Flatbed cutting table	1,702 × 1,702	1,270
Colex	Sharpcut SX1732	Flatbed cutting table	1,702 × 3,200	2,032
Colex	Sharpcut SXC1732 (conveyor)	Flatbed cutting table	1,702 × 3,200	2,032
Colex	Sharpcut SXC2032 / SX2032	Flatbed cutting table	2,000 × 3,150	2,032
Colex	Sharpcut SX3232	Flatbed cutting table	3,200 × 3,200	1,057
Summa	F1612	Flatbed cutting table	1,600 × 1,200	1,000
Summa	F1832	Flatbed cutting table	1,840 × 3,200	1,000
Summa	F3220	Flatbed cutting table	3,270 × 2,100	1,000
Summa	F3232	Flatbed cutting table	3,270 × 3,200	1,000
iECHO	BK4-2516	Flatbed cutting table	1,600 × 2,500	1,800
iECHO	BK4-1312	Flatbed cutting table	1,200 × 1,300	1,800
iECHO	TK4S-2516	Flatbed cutting table	1,600 × 2,500	1,500
iECHO	TK4S-3521	Flatbed cutting table	2,100 × 3,500	1,500
iECHO	TK4S-2532	Flatbed cutting table	3,200 × 2,500	1,500
iECHO	PK0604 (and PK0604 Plus)	Flatbed cutting table	400 × 600	1,000
iECHO	PK0705 (and PK0705 Plus)	Flatbed cutting table	530 × 750	1,000
iECHO	PK1209 (Pro)	Flatbed cutting table	900 × 1,200	1,500
Elitron	Kombo SD+ 16.20	Flatbed cutting table	1,600 × 2,000	1,700
Elitron	Kombo SDC+ 32.20 (conveyor) / SD+ 32.20 (fixed)	Flatbed cutting table	3,200 × 2,000	1,700
Elitron	Kombo SD+ 40.25	Flatbed cutting table	4,000 × 2,500	1,700
Mimaki	CFL-605RT	Flatbed cutting table	610 × 510	423
Graphtec	FC9000-160	Roll cutter / plotter	1,626 × 50,000	1,485
Graphtec	FC9000-140	Roll cutter / plotter	1,372 × 50,000	1,485
Graphtec	FC9000-100	Roll cutter / plotter	1,067 × 50,000	1,485
Summa	S One D160 (S1D160)	Roll cutter / plotter	1,580 × 50,000	1,131
Summa	S One D140 (S1D140)	Roll cutter / plotter	1,385 × 50,000	1,131
Summa	S2 T160 (S Class 2 T-series)	Roll cutter / plotter	1,580 × 50,000	1,414
Summa	S2 T140 (S Class 2 T-series)	Roll cutter / plotter	1,350 × 50,000	1,414
Roland	CAMM-1 GR2-640	Roll cutter / plotter	1,627 × 50,000	1,530
Roland	CAMM-1 GR2-540	Roll cutter / plotter	1,372 × 50,000	1,530

Printers#

Print widths are in millimetres. The fastest mode is usually a draft mode; the default mode a new printer starts with is slower.

Wide-format printer presets
Maker	Model	Type	Max print width (mm)	Print modes	Fastest mode (m²/h)
HP	Latex 315	Roll-to-roll printer	1,371	6	48
HP	Latex 335	Roll-to-roll printer	1,625	7	50
HP	Latex 365	Roll-to-roll printer	1,625	7	91
HP	Latex 630 / 630 W	Roll-to-roll printer	1,625	10	35
HP	Latex 700 / 700 W	Roll-to-roll printer	1,625	10	105
HP	Latex 800 / 800 W	Roll-to-roll printer	1,625	10	122
HP	Latex 830 / 830 W	Roll-to-roll printer	1,625	10	36
HP	Latex 1500	Roll-to-roll printer	3,200	5	74
HP	Latex 2700 / 2700 W	Roll-to-roll printer	3,200	11	121
HP	Latex R1000 / R1000 Plus	Hybrid (roll and rigid)	1,625	6	56
HP	Latex R2000 / R2000 Plus	Hybrid (roll and rigid)	2,489	6	86
Epson	SureColor S40600	Roll-to-roll printer	1,615	5	57
Epson	SureColor S60600 / S60600L	Roll-to-roll printer	1,615	5	95
Epson	SureColor S80600 / S80600L	Roll-to-roll printer	1,615	5	95
Epson	SureColor S7170	Roll-to-roll printer	1,625	3	71
Epson	SureColor S8170	Roll-to-roll printer	1,625	5	130
Epson	SureColor S9170	Roll-to-roll printer	1,615	4	94
Epson	SureColor R5070 / R5070L	Roll-to-roll printer	1,615	4	27
Epson	SureColor V7000	Flatbed printer	2,500	5	43
Canon	Colorado 1630	Roll-to-roll printer	1,625	13	111
Canon	Colorado 1650	Roll-to-roll printer	1,625	15	159
Canon	Colorado M5 / M5W	Roll-to-roll printer	1,625	28	159
Canon	Colorado M3 / M3W	Roll-to-roll printer	1,625	28	111
Canon	Arizona 1300 series (1340/1360/1380 GT & XT)	Flatbed printer	2,500	12	51
Canon	Arizona 2300 series (2340/2360/2380 GTF & XTF)	Flatbed printer	2,500	12	89
Roland DG	TrueVIS VG3-640	Roll-to-roll printer	1,600	11	30
Roland DG	TrueVIS VG3-540	Roll-to-roll printer	1,346	2	29
Roland DG	TrueVIS SG3-540	Roll-to-roll printer	1,346	1	10
Roland DG	TrueVIS SG3-300	Roll-to-roll printer	736	1	7
Roland DG	VersaUV LEC2-640	Roll-to-roll printer	1,600	1	11
Roland DG	VersaUV LEC2-330	Roll-to-roll printer	736	1	9
Roland DG	VersaUV LEF2-300	Flatbed printer	770	2	2
Roland DG	VersaUV LEF2-200	Flatbed printer	508	2	1
Mimaki	JV330-160 / CJV330-160	Roll-to-roll printer	1,610	15	100
Mimaki	UCJV330-160	Roll-to-roll printer	1,610	18	55
Mimaki	UJF-7151 plusII	Flatbed printer	710	9	8
Mimaki	JFX200-2513 EX	Flatbed printer	2,500	5	35
Mimaki	JFX600-2513	Flatbed printer	2,500	6	200
EFI	VUTEk Q3r	Roll-to-roll printer	3,500	1	558
EFI	VUTEk Q5r	Roll-to-roll printer	5,200	1	672
EFI	VUTEk h5 / h5+	Hybrid (roll and rigid)	3,200	2	393
EFI	VUTEk Q3h XP	Hybrid (roll and rigid)	3,340	2	905
Agfa	Jeti Tauro H3300 S	Hybrid (roll and rigid)	3,340	1	450
Agfa	Jeti Tauro H3300 HS	Hybrid (roll and rigid)	3,340	1	680
Agfa	Jeti Tauro H3300 UHS	Hybrid (roll and rigid)	3,340	1	905
Agfa	Anapurna H2050i LED	Hybrid (roll and rigid)	2,050	6	104
Agfa	Jeti Mira LED (MG2716 HS / MG2732 HS)	Flatbed printer	2,690	6	248
swissQprint	Nyala 5	Flatbed printer	3,240	4	253
swissQprint	Impala 5	Flatbed printer	2,540	4	227
swissQprint	Kudu	Flatbed printer	3,240	4	341
swissQprint	Karibu S	Roll-to-roll printer	3,400	4	330

Presses#

Press presets work differently: every value carries its source and a confidence badge, unverified values are never copied, and costs and makeready times always start empty. See Presses: sheetfed offset and digital.

Finishing machines#

Finishing presets follow the press rule and go one step further: they say what a machine is, never how fast you run it. Add finishing machine lists them by kind:

Generic configurations for every wave of box work: platen die-cutters (with stripping, or stripping and blanking), a rotary die-cutter, folder-gluers for straight line, crash-lock bottom or all four glue styles, flexo folder-gluers with 1, 2 or 4 print stations, a buckle folder, a laminator, a window patcher and an "other" machine.
Makers' models with a published rated maximum: the Bobst Expertfold folder-gluers (up to 450 m/min; up to 28,000 boxes an hour on 4 and 6-corner boxes) and the Heiber + Schröder WP 1400 Master window patcher (up to 40,000 pieces an hour on short blanks).

A preset copies the kind, the speed unit, the glue styles or print stations and the consumable's name. The planning speed, setup and changeover minutes, waste, speed factors and every cost start empty. A rated maximum is shown beside the empty speed as a hint, never used as the value: see Finishing machines.

Your model isn't listed#

Choose Custom machine or Custom printer in the same dialog (Add blank machine of a kind for finishing machines), and copy the figures from your manufacturer's data sheet: the working area, maximum speed and acceleration for a cutter, and each print mode's speed for a printer. Then run a timed test and calibrate.

Using a preset#

Published figures and estimated starting values#

Cutting machines#

Printers#

Presses#

Finishing machines#

Your model isn't listed#

See also

Help us improve AutomatePrint